Triumph t120r petrol tank repair
My fuel tank sprung a leak I repaired it with solder, plastic metal, and a chemical liner. I am also going to spray the tank.
Duration : 0:9:11
Rust Removal From A Motorcycle Gas Tank Using Electrolysis
A simple Electrolysis set up using a PC power supply as the power source, a wire hanger as the sacrificial anode and a mixture of water and Sodium Carbonate also known as Washing Soda/Laundry Soda. You can make your own Sodium Carbonate by heating up baking soda in the oven for an hour or so, above 300 degree Fahrenheit (149 degree Celsius). I read that some people are you using oxyclean since the active ingredient is Sodium Carbonate. The solution in the tank is a mixture of 5 gallon of water and 1/2 cup of Sodium Carbonate. I topped the tank off, put in the sacrificial anode, connect power to the anode, ground wire to the tank and turn on the power. You should start to see bubbles if it is working right. Make sure not to let the anode touch the gas tank. Also make sure you do this in a well ventilated location because the reaction will release Hydrogen gas and any spark might cause an explosion. I let it do its thing for about 20 hours and after checking the tank looked like it did a really good job. It looked liked all the rust was gone but I decided to do again just incase i missed anything.
Duration : 0:1:34
How to clean a Ninja 250 motorcycle gas tank with Vinegar. Part 4
How quickly the Vinegar attacks. Skip the darness and go to 1:20
Duration : 0:3:49
*BIKE IS FOR SALE*Remove the Stock Seat & Install Danny Gray Solo Seat on Harley Davidson Rocker C
**THIS BIKE IS FOR SALE***SEND MESSAGE IF INTERESTED*** Click Here: to Purchase Your Shaving Products: http://www.ShaveNation.com/products
How to Remove the Stock Seat and Chrome Flip Seat Support Assembly and Install a Danny Gray Solo Seat on a Harley Davidson Rocker C Motorcycle 2008 2009 2010 2011 from Start to Finish To Remove the Large Gap Between the Rear Fender and the Seat.
Tutorial, instructions, and directions.
Misc: Remove Bolts apply loctite as needed. Remove Seat. Fill unused holes with bolts, grommets, or silicone. Use Heat shrink to splice and seal wires, wiring. Use penetrating agent and or wd40 to loosen bolts or hammer and screwdriver in counterclockwise direction. Battery compartment below seat. 8 9 10 11 model year years.
Duration : 0:7:16
painting a motorcycle tank part one
part one, remove emblems, sand all blemishes with sand paper, apply bondo to dings, sand smooth. TAKE YOUR TIME, it pays off
Duration : 0:3:51
AIX 2.0 (BF2 Mod) ‘Casual’ Review #3 – Kits & Soldier Weapons
My last video was too long, so here are the kit and soldier weapons in a seperate video, remember, you can get AIX mod from:
www.aixtended.com
For free, as long as you have BF2
Duration : 0:1:56
Draining fuel tank
Draining the fuel tank of a Suzuki GS650G by setting the petcock to PRI which drains it out using gravity instead of ON which uses the vacuum from the carbs. I am draining the fuel tank because I am going to replace the fuel valve and petcock assembly.
Duration : 0:0:14
Part 6of6: Motorcycle Rust Removal and Resoration using a Kreem Kit Part 6 of 6; The liner
Here is a great one liner: Kreem Koat it! This will fix any metal tank if it will fix this one! After carefully removing all rust and debris from this Honda tank, it is ready for the tank liner. Use in a very well ventilated area and keep the tank moving in a rolling pattern for 5 minutes even after the excess is poured out! This will prevent any puddles from forming. You want a uniform coating of Kreem liner in the tank.
Duration : 0:2:47
McCuff Motorcyle Gas Tank Spill Protector Chopper Industry
McCuff Motorcyle Gas Tank Spill Protector Chopper Industry Show Video With Billy Carmen
Duration : 0:2:57
Atelier Meijer – Carla’s Harley Davidson fuel tank airbrush
Jan Meijer airbrushes the fueltank of a Custom build Harley Davidson for Carla
Duration : 0:7:19